Protector Stainless Steel Radioisotope Laboratory Hoods

Protector Stainless Steel Radioisotope Laboratory Hoods provide protection from applications requiring the use of radiochemicals. They feature fully sealed integral work surfaces and coved interiors to facilitate decontamination.

Available in 4, 5, 6 and 8-foot widths, these benchtop hoods feature a corrosion-resistant Type 304 stainless steel interior. The one-piece liner is free of joints, cracks or crevices to prevent build-up of residue and simplify decontamination procedures.

Use Our Product Selection Tools

Scout™ Lab Equipment Selector

Let Scout lead you to the right laboratory hood or evaporation equipment for your application.

With fully sealed integral work surfaces and coved interiors, these benchtop stainless steel-lined hoods provide protection from applications requiring the use of radiochemicals.

Features (All Models)

By-pass airflow design and by-pass block
Curved Eco-Foil™ air foil allows air to sweep the work surface while Clean-Sweep™ openings pull inflow air from under the air foil
Cord-Keeper™ slots on left and right side of air foil
Glacier white, powder-coated steel exterior
Seamless Type 304 stainless steel liner with radiused corners, integral work surface and pre-set baffle(s)
Black enamel-coated hardboard supporting surface
Powder-coated aluminum sash handle with Clean-Sweep™ openings and Clean-Sweep™ slots on the powder-coated stainless steel sash tracks
Tempered safety glass vertical-rising sash with cable and pulley
Removable front and side panels and front access panels for access to plumbing and electrical wiring
Pre-wired LED lighting with vapor-proof design and ADA-compliant light and blower switches. Lighting rated to 50,000 hours
11.0" OD Type 304 stainless steel exhaust connection(s)

Fixtured Models May Feature

Two pre-plumbed service fixtures with forged brass valves, lower right side with brass tubing for gas and lower left side with copper tubing for air. Components for converting either or both fixtures to cold water and vacuum are provided. Inlet tubing is not provided.
One pre-wired GFCI electrical duplex receptacle on lower right side and, on 8' models only, one additional pre-wired GFCI electrical duplex receptacle on lower left side

Options

4', 5', 6' and 8' widths

Required Accessories (Not Included)

Dedicated remote blower
Ductwork (type 304 stainless steel is recommended)
Base cabinet or stand

Optional Accessories

Service Fixture Kits
Electrical Duplex Kits
Guardian Airflow Monitor Kits
Sash Stop Kits
Ceiling Enclosure and Rear Finish Panel Kits

Compliance

SEFA 1
NFPA 45
ASTM E84-09C
ASHRAE 110
ANSI Z9.5
SEFA 8
CFR 29, Part 1910
UL 61010-1
CAN/CSA Standard C22.2 No. 61010.1
UL 1805

Our Product Representatives Are Here To Help

Webinar on Managing Lab Air with Chemical Fume Hoods

For many laboratories, managing air quality through engineered controls is essential for worker safety and comfort. However, with numerous options available for fume extraction and air purification, deciding on an engineered solution that best suits your lab’s current and future needs is not always straightforward.

Fume Hoods Overview 2013

Literature & Resources

En Español
- Spanish-Language Fume Hoods Catalog
  Campanas extractoras para laboratorios Protector y Basic
  
  Proporciona beneficios, especificaciones y fotos.
  
  This Spanish-language brochure contains an overview, specifications and ordering information on Protector Premier, XStream, XL and Special Application Fume Hoods, and Basic series Fume Hoods. Ordering information on accessories is also included.
Brochures
- Protector Special Application Laboratory Fume Hoods Brochure
  This brochure contains ordering information, specifications and dimensional data for Protector Stainless Steel Radioisotope, Stainless Steel Perchloric Acid and PVC Perchloric & Acid Digestion Laboratory Hoods.
User's Manuals
- Protector Stainless Steel Radioisotope Laboratory Fume Hoods
  For Protector Stainless Steel Radioisotope Laboratory Fume Hood models 1204, 1205, 1206 and 1208 Series.
- Wiring Diagram for 4', 5' and 6' Protector Series Laboratory Hoods (115 volt)
  For Protector XStream, Premier, XL Benchtop, XL Floor-Mounted, Stainless Steel Radioisotope, Stainless Steel Perchloric Acid, PVC Perchloric Acid and PVC Acid Digestion Laboratory Hoods for 115 volt, 60 Hz operation. Part number is 9826500, Rev. -.
- Wiring Diagram for 4', 5' and 6' Protector Series Laboratory Hoods (230 volt)
  For Protector XStream, Premier, XL Benchtop, XL Floor-Mounted, Stainless Steel Radioisotope, Stainless Steel Perchloric Acid, PVC Perchloric Acid and PVC Acid Digestion Laboratory Hoods for 230 volt, 50/60 Hz operation. Part number is 9834200, Rev. -.
- Wiring Diagram for 8' Protector Series Laboratory Hoods
  For Protector XStream, Premier, XL Benchtop, XL Floor-Mounted, Stainless Steel Radioisotope, Stainless Steel Perchloric Acid, PVC Perchloric Acid and PVC Acid Digestion Laboratory Hoods for 115 volt, 60 Hz operation. Part number is 9827300, Rev. -.
- Wiring Diagram for 8' Protector Series Laboratory Hoods
  For Protector XStream, Premier, XL Benchtop, XL Floor-Mounted, Stainless Steel Radioisotope, Stainless Steel Perchloric Acid, PVC Perchloric Acid and PVC Acid Digestion Laboratory Hoods for 230 volt, 50/60 Hz operation. Part number is 9834300, Rev. -.
3-Part Specs
- Protector Stainless Steel Radioisotope Laboratory Hoods Specifications
Declarations of Conformity
- CE Declaration of Conformity - Protector Stainless Steel Radioisotope Hoods
  For 1204 Series, 1205 Series, 1206 Series, and 1208 Series Protector Stainless Steel Radioisotope Fume Hoods
Installation Qualification / Operation Qualification
- Installation Qualification/Operation Qualifications Protocol for Protector Series Laboratory Fume Hood
  For validation of predetermined Protector Series Laboratory Fume Hood specifications. Provides a checklist of installation and operation qualifications to complete when beginning operation on new or used Protector Series Laboratory Fume Hoods.

Search

Protector Stainless Steel Radioisotope Laboratory Hoods

Use Our Product Selection Tools

Scout™ Lab Equipment Selector

Features (All Models)

Fixtured Models May Feature

Options

Required Accessories (Not Included)

Optional Accessories

Compliance

Our Product Representatives Are Here To Help

Application Specialists

Senior Application Specialist

Product Service

Product Service Representative

Webinar on Managing Lab Air with Chemical Fume Hoods

Fume Hoods Overview 2013

Literature & Resources

En Español

Spanish-Language Fume Hoods Catalog

Brochures

Protector Special Application Laboratory Fume Hoods Brochure

User's Manuals

Protector Stainless Steel Radioisotope Laboratory Fume Hoods

Wiring Diagram for 4', 5' and 6' Protector Series Laboratory Hoods (115 volt)

Wiring Diagram for 4', 5' and 6' Protector Series Laboratory Hoods (230 volt)

Wiring Diagram for 8' Protector Series Laboratory Hoods

Wiring Diagram for 8' Protector Series Laboratory Hoods

3-Part Specs

Protector Stainless Steel Radioisotope Laboratory Hoods Specifications

Declarations of Conformity

CE Declaration of Conformity - Protector Stainless Steel Radioisotope Hoods

Installation Qualification / Operation Qualification

Installation Qualification/Operation Qualifications Protocol for Protector Series Laboratory Fume Hood

Related Products

Get newsletters on lab safety, design and exclusive offers.